| there is a TSB to flash the TIPM
here it is right from chrysler
SUBJECT:
Flash - Rear Wiper Stops Operating with Diagnostic Trouble Codes B231B And B2215
OVERVIEW:
This bulletin involves Flash Reprogramming the Totally Integrated Power Module (TIPM)
with updated software.
MODELS:
2006 (PT) PT Cruiser
2007 (PM) Caliber
NOTE: This bulletin applies to PM vehicles built before May 27, 2006 (MDH 0527XX)
and all PT vehicles built before June 2, 2006 (MDH 0602XX)
SYMPTOM/CONDITION:
The rear wiper may stop operating. Upon further investigation the technician may find that
the following Diagnostic Trouble Codes (DTC's) are present::
A. B2215 - FCM Internal
B. B231B - Rear Wiper Motor Control Circuit Low
DIAGNOSIS:
1. Connect the StarSCAN® to the vehicle.
2. Turn the ignition on.
3. With the Scan Tool, clear all TIPM DTC's.
4. Turn the Rear Windshield Wipers on.
5. Does the rear wiper operate?
6. Yes >> Perform the Repair Procedure.
7. No >> This bulletin does not apply, additional diagnosis is required.
SPECIAL TOOLS / EQUIPMENT REQUIRED:
NPN Battery Charger
CH9401 StarSCAN® Tool
NUMBER: 08-027-06
GROUP: Electrical
DATE: June 5, 2006
CH9404 StarSCAN® Vehicle Cable
CH9409 StarSCAN® Documentation Kit
CH9410 StarSCAN® Ethernet Cable, 12 ft.
CH9412 StarSCAN® Software Update Device Kit
TechCONNECT PC or equivalent
REPAIR PROCEDURE - USING THE INTERNET TO RETRIEVE THE FLASH FILE:
NOTE: Before performing this Repair Procedure, the operating software in the
StarSCAN®; must be programmed with software release level 6.06 or higher.
The software release level is visible in the blue header at the top of the
StarSCAN® screen.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1. Install a battery charger and verify that the charging rate provides approximately 13.5
volts. Set the battery charger to continuous charge. Do not allow the charger to time
out during the flash process. Remove the charger from the battery when the flash
process is complete.
2. Connect the CH9410 StarSCAN® ethernet cable to the StarSCAN® and the dealer's
network drop.
3. Connect the CH9404 StarSCAN® vehicle cable to the StarSCAN® and the vehicle.
4. Power ON the StarSCAN®.
5. Retrieve the old TIPM part number. Using the StarSCAN® at the “Home” screen:
a. Select “ECU View”
b. Touch the screen to highlight the appropriate ECU in the list of modules.
c. Select “More Options”
d. Select “ECU Flash”
e. Record the part number at the top of the “Flash ECU” screen for later reference.
f. Select “Browse for New File”. Follow the on screen instructions.
g. Highlight the listed calibration.
h. Select “Download to Scantool”.
i. Select “Close” after the download is complete, then select “Back”.
j. Highlight the listed calibration.
k. Select “Update Controller”. Follow on screen instructions.
l. When the update is complete, select “OK”.
m.Verify the part number at the top of the “Flash ECU” screen has updated to the new
part number.
08-027-06 -2-
NOTE: Due to the TIPM programming procedure, a DTC may be set in other modules
(PCM, TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so equipped.
Some DTC's may cause the MIL to illuminate. From the “Home” screen select
“System View”. Then select “All DTCs”. Press “Clear All Stored DTCs” if
there are any DTCs shown on the list.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation No: Description Amount
18-89-01-12 Reprogram TIPM Module (B) 0.3 Hrs.
FAILURE CODE:
ZZ Service Action
-3- 08-027-06
__________________
Team Rev Support Vehicle for now, when gas hits 5 bucks, 2008 SRT-4 black.  |