crmdevries

I am new this forum and just wanted to introduce myself. I recently purchased a 2007 Dodge Caliber. I had it rebuilt because it was in an accident and therfore does not have any warranty. With this in mind I was hoping some of you can asssit me? I cannot seem to get the rear wiper to work although it did previously. Does anyone have any ideas? I have read in various other forums that perhaps Chrysler has a few problems with this?

Thank you.

bigtsr

Make sure the rear wiper arm is not just slipping on the drive post.
In the 2 years I have owned a Caliber I have read several posts
regarding the rear wiper malfunction,it has been posted also that
the fuse that carries power to it also controls sunroof.
Is the sunroof (if you have one) working?
The other posts indicate it is also a part of the TIPM(Totally Integrated
Powercantrol Module) circuit which controls the current sensing of
peripheral accessories and will shut them down if it senses overcurrent.
The TIPM is part of the fusebox assy drivers side under the hood.

__________________
Black SXT 2.0L-CVT-Cruise-Security-Tint-Sill plates-
Shorty antenna-Bumper protection-Exhaust mod-
Upholstered front headrests-Painted engine cover
Ordered April 15/06-Delivered August 18/06

stripedHEMI766

there is a TSB to flash the TIPM


here it is right from chrysler








SUBJECT:
Flash - Rear Wiper Stops Operating with Diagnostic Trouble Codes B231B And B2215

OVERVIEW:
This bulletin involves Flash Reprogramming the Totally Integrated Power Module (TIPM)
with updated software.

MODELS:
2006 (PT) PT Cruiser
2007 (PM) Caliber

NOTE: This bulletin applies to PM vehicles built before May 27, 2006 (MDH 0527XX)
and all PT vehicles built before June 2, 2006 (MDH 0602XX)

SYMPTOM/CONDITION:
The rear wiper may stop operating. Upon further investigation the technician may find that
the following Diagnostic Trouble Codes (DTC's) are present::
A. B2215 - FCM Internal
B. B231B - Rear Wiper Motor Control Circuit Low

DIAGNOSIS:
1. Connect the StarSCAN® to the vehicle.
2. Turn the ignition on.
3. With the Scan Tool, clear all TIPM DTC's.
4. Turn the Rear Windshield Wipers on.
5. Does the rear wiper operate?
6. Yes >> Perform the Repair Procedure.
7. No >> This bulletin does not apply, additional diagnosis is required.

SPECIAL TOOLS / EQUIPMENT REQUIRED:
NPN Battery Charger
CH9401 StarSCAN® Tool
NUMBER: 08-027-06
GROUP: Electrical
DATE: June 5, 2006
CH9404 StarSCAN® Vehicle Cable
CH9409 StarSCAN® Documentation Kit
CH9410 StarSCAN® Ethernet Cable, 12 ft.
CH9412 StarSCAN® Software Update Device Kit
TechCONNECT PC or equivalent

REPAIR PROCEDURE - USING THE INTERNET TO RETRIEVE THE FLASH FILE:
NOTE: Before performing this Repair Procedure, the operating software in the
StarSCAN®; must be programmed with software release level 6.06 or higher.
The software release level is visible in the blue header at the top of the
StarSCAN® screen.


NOTE: If this flash process is interrupted/aborted, the flash should be restarted.

1. Install a battery charger and verify that the charging rate provides approximately 13.5
volts. Set the battery charger to continuous charge. Do not allow the charger to time
out during the flash process. Remove the charger from the battery when the flash
process is complete.
2. Connect the CH9410 StarSCAN® ethernet cable to the StarSCAN® and the dealer's
network drop.
3. Connect the CH9404 StarSCAN® vehicle cable to the StarSCAN® and the vehicle.
4. Power ON the StarSCAN®.
5. Retrieve the old TIPM part number. Using the StarSCAN® at the “Home” screen:
a. Select “ECU View”
b. Touch the screen to highlight the appropriate ECU in the list of modules.
c. Select “More Options”
d. Select “ECU Flash”
e. Record the part number at the top of the “Flash ECU” screen for later reference.
f. Select “Browse for New File”. Follow the on screen instructions.
g. Highlight the listed calibration.
h. Select “Download to Scantool”.
i. Select “Close” after the download is complete, then select “Back”.
j. Highlight the listed calibration.
k. Select “Update Controller”. Follow on screen instructions.
l. When the update is complete, select “OK”.
m.Verify the part number at the top of the “Flash ECU” screen has updated to the new
part number.
08-027-06 -2-
NOTE: Due to the TIPM programming procedure, a DTC may be set in other modules
(PCM, TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so equipped.
Some DTC's may cause the MIL to illuminate. From the “Home” screen select
“System View”. Then select “All DTCs”. Press “Clear All Stored DTCs” if
there are any DTCs shown on the list.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation No: Description Amount
18-89-01-12 Reprogram TIPM Module (B) 0.3 Hrs.
FAILURE CODE:
ZZ Service Action
-3- 08-027-06

__________________
Team Rev Support Vehicle for now, when gas hits 5 bucks, 2008 SRT-4 black.