SniperSrt

i was just wondering if any one could give me a good starting point on how long or short to make the rod on the wga i just recived my ptp wga in the mail and i really want to install it but i need a good starting point any help thanks.

__________________
Mods.
Mopar stage 1
Mopar blow off plate
Ngk colder plugs
ptp downpipe
Ptp inlet pipe
ptp wga
K&n drop in filter
Agp catch can
Bwoody check valve
Mpx strut bar
Aeroforce scan gauge

Anonymous

Preload the WGA with 1.5 to 2mm worth of preload (force the WGA over the pin on the flapper arm). This is a good starting point for our WGA.

Let me know if you need any help, thanks.

SniperSrt

ok when you say 1 to 2 mm dose that mean shorter than the stock wga i sorry if im sounding like and idiot but i dont want to mess anything up

__________________
Mods.
Mopar stage 1
Mopar blow off plate
Ngk colder plugs
ptp downpipe
Ptp inlet pipe
ptp wga
K&n drop in filter
Agp catch can
Bwoody check valve
Mpx strut bar
Aeroforce scan gauge

mvs1

I'm pretty sure what he means is that if you have the WG closed and the actuator rod sitting by the WG stud that you will need to pull the rod 1.5-2 mm to get the rod eyelet over the WG arm's stud...does that make sense? If not then set the rod shorter then the stock rods overall length by approx. 1/4", attach and go for a ride, record max boost and then shortent the rod to increase boost or lengthen the rod to lower peak boost.

__________________
K&N Drop In, MPx DP w/Cat, PTP UPP w/TurboSmart VeePort, MPx STB, Aeroforce Interceptor II w/SRT Faceplate, Blu/Wht Prosport Oil Pressure gauge, BWoody Check Valve, NGK BKR6EIX, MS 1, Progress Rear Sway, PTP WGA, RT Clamp @ 3.27v, BWoody Traction Bars, AGP MM.

w/MS1 w/MS1 & Clamp

srt4 firefighter

Mvs1 is right. Do exactly what he said and u should be fine. Let us know how it goes.

__________________
Mods

ms1, aeroforce scangauge,uego wideband, hks bov, Ngk iridium spark plugs, Ptp 4 inch intake with spectra filter, pnp Ptp map tip clamp, Ptp wga, turbosmart dual stage boost controller, mechanical boost gauge, mpx d/p, muffler delete, small battery kit.

Best time.
13.319 @ 111 mph.

Anonymous

Thanks for the help guys!

SniperSrt

the install is goin well i have been taking my sweet time putting it in cause im saving gas by bumming rides to and from work lol but ill let you guys know when i take it for a test drive

__________________
Mods.
Mopar stage 1
Mopar blow off plate
Ngk colder plugs
ptp downpipe
Ptp inlet pipe
ptp wga
K&n drop in filter
Agp catch can
Bwoody check valve
Mpx strut bar
Aeroforce scan gauge

SniperSrt

well all i have to say is thanks ptp for another great product the test drive went well and im at at a loss for words but thanks to all that helped me with my questions

__________________
Mods.
Mopar stage 1
Mopar blow off plate
Ngk colder plugs
ptp downpipe
Ptp inlet pipe
ptp wga
K&n drop in filter
Agp catch can
Bwoody check valve
Mpx strut bar
Aeroforce scan gauge

Anonymous

LOL, you have to love the TQ hit of the PTPerformance WGA.